 |
The carbon fiber press machine is used to apply pressure and heat to layers of carbon fiber material to form a composite material. The machine typically consists of a large press, which can apply several tons of pressure, and heating elements that can reach temperatures up to 400 degrees Celsius.
| Specification | 400T | 500T | 800T | 1000T | 1200T | |
| Total Pressure | KN | 4000 | 5000 | 8000 | 10000 | 12000 |
| Dimension of Worktable Surface | mm | 1400x1400 | 1700x1700 | 1800x1800 | 2000x2000 | 2200x2200 |
| Main Motor Power | KW | 18.5 | 18.5 | 18.5 | 22 | 22 |
| Main Cylinder（Dxquantity） | mm | Φ440x1 pcs | Φ500x1 pcs | Φ320x1 pcs | Φ360x1 pcs | Φ400x1 pcs |
| Lifting Cylinder（Dxquantity） | mΦ80x4 pcsm | Φ80x4 pcs | Φ80x4 pcs | Φ80x4 pcs | Φ100x4 pcs | Φ120x4 pcs |
| Max Pressure | Mpa | 25 | 25 | 25 | 25 | 25 |
| Cylinder Stroke | mm | 800 | 800 | 800 | 800 | 900 |
| Close Speed of the Worktable | mm/s | 0~200 Adjustable | ||||
| Table linear Velocity | mm/s | 0~100 Adjustabl | ||||
| Electric Control System | - | Programmable PLC | ||||
| System Power Supply | - | 380V/50Hz | ||||
| Main Machine Size | mm | 2600x1400x4000 | 3000x1700x4000 | 3000x1800x4000 | 3500x2000x4000 | 3600x2200x4000 |
| Main Machine Weight | KG | 18000 | 18000 | 23000 | 28000 | 32000 |
1. Frame plate vulcanizing press is composed of hot plates, plates, up and down platforms, piston stroke, hydro-cylinder, hydraulic station and electrical control system. It can be equipped with push-pull mould device to move the mould on the machine.
2. Plates are constituted with welded Q235 steel plates through mechanical ball blast rust removal, spraying zinc rich series paint, shake to remove stress, then transferred into mechanical producing.
Hot plates are obtained by 35# steel plates after normalizing handling and then adopting double scale rolling. It is equipped with a set of electric control valves to realize the automatic adjusting of steaming temperature.
3. Up and down platforms adopts Q235 steel plates. In order to guarantee the make precision, it is applied with automatic cutting baiting, mechanical slicer producing welded groove, carbon dioxide gas shielded welding. It all adopts alloy welding wire welding and after welding takes whole enter into stove to go on the hot treatment to remove the welding stress exhaustively.
Hydro-cylinder adopts ZG270-500 and piston stroke adopts hard cold chilled alloy cast iron. And sealing structure applies the combined structure with double sealing ring and one dustproof ring to guarantee longer service.
4. Electrical control system adopts PLC automatic control to realize automatic closing, opening mould and gas exit equipment. It can also switch into hand control.
5. Before leaving factory, this plate vulcanizing press needs to pass 24 hours' pressure test, pressure maintaining to test the bearing of the hydro-cylinder and piston stroke and guarantee no oil leakage and seeping to avoid unnecessary quality problems.
6. We can design and manufacture all kinds of non-standard plate vulcanizing press according to the customers' definite requirements.
Carbon fiber hot forming press is automotive lightweight, unit bathroom, aerospace, rail traffic, city construction, lower-voltage electric appliance. in hot forming carbon fiber materials like electronics housings and sports goods.
1.Rich Experience and Professional Design
We have 19 years experience in Woodworking industry,also has many years exporting experience. Each equipment location,passage will be designed reasonably to meet safety production.
2.Competitive Price
HallMark has own factory,with the same configuration,the price is competitive.And we are familiar with the Chinese market,our suppliers provide high-quality cost-effective accessories.
3.Timely After-sale Service
We have over 15 skilled technicians engineers, 26 after-sales engineers will be sent to the customer's factory to assist in the installation and debugging of the Whole production line until it runs well,and asked for quick responses to customer questions within 8 hours.
4.One-stop Solution
We provide one-stop service, including market analysis and professional technical consultation,Short Cycle Press Line, Paper Impregnation Production Line, Wood Based Panel Production Line, Raw materials ,Equipment installation, personnel training,Professional after-sales service team,Renovation of old equipment,make turnkey projects.
5.Quality Control
Strict quality control of equipment in production and before leaving the factory, and a complete quality management system for purchased parts.Customers are always welcome to make videos or come to the factory to know the production status.
6.Customized
HallMark's engineer team will design the layout according to customer’s factory space and production requirements
The carbon fiber press machine is used to apply pressure and heat to layers of carbon fiber material to form a composite material. The machine typically consists of a large press, which can apply several tons of pressure, and heating elements that can reach temperatures up to 400 degrees Celsius.
| Specification | 400T | 500T | 800T | 1000T | 1200T | |
| Total Pressure | KN | 4000 | 5000 | 8000 | 10000 | 12000 |
| Dimension of Worktable Surface | mm | 1400x1400 | 1700x1700 | 1800x1800 | 2000x2000 | 2200x2200 |
| Main Motor Power | KW | 18.5 | 18.5 | 18.5 | 22 | 22 |
| Main Cylinder（Dxquantity） | mm | Φ440x1 pcs | Φ500x1 pcs | Φ320x1 pcs | Φ360x1 pcs | Φ400x1 pcs |
| Lifting Cylinder（Dxquantity） | mΦ80x4 pcsm | Φ80x4 pcs | Φ80x4 pcs | Φ80x4 pcs | Φ100x4 pcs | Φ120x4 pcs |
| Max Pressure | Mpa | 25 | 25 | 25 | 25 | 25 |
| Cylinder Stroke | mm | 800 | 800 | 800 | 800 | 900 |
| Close Speed of the Worktable | mm/s | 0~200 Adjustable | ||||
| Table linear Velocity | mm/s | 0~100 Adjustabl | ||||
| Electric Control System | - | Programmable PLC | ||||
| System Power Supply | - | 380V/50Hz | ||||
| Main Machine Size | mm | 2600x1400x4000 | 3000x1700x4000 | 3000x1800x4000 | 3500x2000x4000 | 3600x2200x4000 |
| Main Machine Weight | KG | 18000 | 18000 | 23000 | 28000 | 32000 |
1. Frame plate vulcanizing press is composed of hot plates, plates, up and down platforms, piston stroke, hydro-cylinder, hydraulic station and electrical control system. It can be equipped with push-pull mould device to move the mould on the machine.
2. Plates are constituted with welded Q235 steel plates through mechanical ball blast rust removal, spraying zinc rich series paint, shake to remove stress, then transferred into mechanical producing.
Hot plates are obtained by 35# steel plates after normalizing handling and then adopting double scale rolling. It is equipped with a set of electric control valves to realize the automatic adjusting of steaming temperature.
3. Up and down platforms adopts Q235 steel plates. In order to guarantee the make precision, it is applied with automatic cutting baiting, mechanical slicer producing welded groove, carbon dioxide gas shielded welding. It all adopts alloy welding wire welding and after welding takes whole enter into stove to go on the hot treatment to remove the welding stress exhaustively.
Hydro-cylinder adopts ZG270-500 and piston stroke adopts hard cold chilled alloy cast iron. And sealing structure applies the combined structure with double sealing ring and one dustproof ring to guarantee longer service.
4. Electrical control system adopts PLC automatic control to realize automatic closing, opening mould and gas exit equipment. It can also switch into hand control.
5. Before leaving factory, this plate vulcanizing press needs to pass 24 hours' pressure test, pressure maintaining to test the bearing of the hydro-cylinder and piston stroke and guarantee no oil leakage and seeping to avoid unnecessary quality problems.
6. We can design and manufacture all kinds of non-standard plate vulcanizing press according to the customers' definite requirements.
Carbon fiber hot forming press is automotive lightweight, unit bathroom, aerospace, rail traffic, city construction, lower-voltage electric appliance. in hot forming carbon fiber materials like electronics housings and sports goods.
1.Rich Experience and Professional Design
We have 19 years experience in Woodworking industry,also has many years exporting experience. Each equipment location,passage will be designed reasonably to meet safety production.
2.Competitive Price
HallMark has own factory,with the same configuration,the price is competitive.And we are familiar with the Chinese market,our suppliers provide high-quality cost-effective accessories.
3.Timely After-sale Service
We have over 15 skilled technicians engineers, 26 after-sales engineers will be sent to the customer's factory to assist in the installation and debugging of the Whole production line until it runs well,and asked for quick responses to customer questions within 8 hours.
4.One-stop Solution
We provide one-stop service, including market analysis and professional technical consultation,Short Cycle Press Line, Paper Impregnation Production Line, Wood Based Panel Production Line, Raw materials ,Equipment installation, personnel training,Professional after-sales service team,Renovation of old equipment,make turnkey projects.
5.Quality Control
Strict quality control of equipment in production and before leaving the factory, and a complete quality management system for purchased parts.Customers are always welcome to make videos or come to the factory to know the production status.
6.Customized
HallMark's engineer team will design the layout according to customer’s factory space and production requirements
